1 4

UAVMODEL

WF-1000S60-12K power supply

Name: WF-1000S60-12K power supply
Brand: UAVMODEL
Price: 6900.00 USD
Availability: InStock

$6,900.00

产品型号

预计在付款后 30~40days 天内送达；

Checkout Securely with

无法下单的客户请联系我们；

Tag : battery power supply , drone power supply , Power Supply

1. Overview

1.1 Application Occasions

This high-voltage DC power supply is a custom-made special power supply, featuring small size, light weight, high efficiency, and built-in fan for heat dissipation. Its maximum operating efficiency is ≥97%. The power module adopts an aluminum shell design, which is lightweight, aesthetically pleasing, and waterproof. It can be used as a substitute for imported high-voltage DC module power supplies.

1.2 Product Features

DC-DC Isolated Power Converter: Isolates and converts the input 800V DC power into 60V DC power, with a total output power of 8KW.
High power density, small size, and light weight.
Designed to meet power supply reliability requirements: Equipped with over/undervoltage protection for input, and overvoltage protection, current limiting, short-circuit protection, and overtemperature protection for output.

1.3 Product Photos

(Photos to be inserted here)

1.4 Main Product Specifications

Input Voltage Range	Rated Output Voltage	Rated Output Power	Efficiency	Voltage Regulation Accuracy	Output Ripple and Noise
680~800Vdc	60±0.5Vdc	8KW	≥97%	≤±2%	≤±2%Vo

2. Environmental Conditions

Serial No.	Item	Technical Index	Unit	Remarks
1	Operating Temperature	-40℃~+50℃	℃
2	Storage Temperature	-40℃~+80℃	℃	/
3	Relative Humidity	≤95	%	No condensation (40℃±2℃)
4	Altitude	0-2000	m
5	Atmospheric Pressure	76~106	Kpa	/
6	Heat Dissipation Method	Built-in Air Cooling	/	/

3. Electrical Characteristics

3.1 Input Characteristics

Serial No.	Item	Technical Requirement	Unit	Remarks
1.1	Rated Input Voltage	750	Vdc
1.2	Input Voltage Range	680~800	Vdc
1.3	Maximum Input Current	14	A	In=680Vdc, Po=8KW

3.2 Output Characteristics

Serial No.	Item	Technical Requirement	Unit	Remarks
2.1	Rated Output Voltage	60	Vdc	/
2.2	Output Voltage Range	57~60.5	Vdc
2.3	Rated Output Current	134	A	/
2.4	Maximum Output Current	150	A	/
2.5	Rated Output Power	8	KW	/
2.6	Output Efficiency	≥97	%	In=750Vdc, Half Load
2.7	Voltage Regulation Accuracy	±1	%	/
2.8	Source Regulation	±1	%	/
2.9	Load Regulation	±1	%	/
2.10	Output Ripple and Noise	±2	%/Vo	Bandwidth limited to 20MHz; 10uF electrolytic capacitor and 0.1uF film capacitor connected in parallel at the test terminal; 750V input, rated load
2.11	Temperature Coefficient	±0.02	%/℃	/
2.12	Output Rise Time	≤200	ms	/
2.13	Power-on Output Delay	≤5	S	Rated input
2.14	Power-on/Power-off Overshoot Amplitude	△V: ≤±5	%	/
2.15	Dynamic Response Overshoot	△V: ≤±5	%	/
2.16	Dynamic Response Recovery Time	≤2	ms	25%~50%~25% or 50%~75%~50% load change, 25℃

3.3 Protection Characteristics

Serial No.	Item	Technical Requirement	Unit	Remarks
3.1	Input Undervoltage Protection	620~640	Vdc	Hysteresis >10V
3.2	Input Undervoltage Recovery	≤650	Vdc
3.3	Input Overvoltage Protection	820~840	Vdc	Hysteresis >10V
3.4	Input Overvoltage Recovery	≥800	Vdc
3.5	Input Reverse Connection Protection	No damage in case of reverse connection	-	Input 800Vdc reversed
3.6	Output Overvoltage Protection	63~66	Vdc	Self-recoverable
3.7	Output Overcurrent Protection	155~175	A	Self-recoverable
3.8	Output Short-Circuit Protection	Available	-	Self-recoverable
3.9	Overtemperature Protection	75	℃	Case temperature
3.10	Overtemperature Recovery	65	℃

4. Safety Characteristics

Serial No.	Item		Test Condition	Remarks
1	Dielectric Strength	Input to Output	2500Vdc/2mA/1min	No arcing, no breakdown
		Input to Enclosure	2000Vdc/2mA/1min
		Output to Enclosure	500Vdc/2mA/1min
2	Insulation Resistance	Input to Output	≥10MΩ @ 500Vdc	Under normal atmospheric pressure, relative humidity 90%, test DC voltage 500V
		Input to Enclosure	≥10MΩ @ 500Vdc
		Output to Enclosure	≥10MΩ @ 500Vdc

5. Other Characteristics

5.1 Flame Retardant Requirement

The flame retardant grade of the PCB used in the system shall meet the V-0 requirement specified in GB4943.1-2011.
The flame retardant grade of the insulated cables shall meet the requirements specified in GB/T 18380.12-2008.
The flame retardant grade of other insulating materials shall meet the V1 requirement specified in GB4943.1-2011.

5.2 System Noise

The system noise shall not exceed 55dB(A).

5.3 System Reliability

MTBF \geq 100 \text{ Khour}

Test Conditions: 25℃, rated input, full-load output, estimated by MIL-HDBK-217F Notice2 stress method.

5.4 Protection Grade

The protection grade shall meet the IP54 requirement. No water accumulation is allowed on the top of the power supply enclosure.

5.5 Three-proof (Moisture-proof, Mildew-proof, Salt Spray-proof)

The printed circuit boards, connectors, and other circuits in the product shall be treated with moisture-proof, mildew-proof, and salt spray-proof measures. Among them, the salt spray resistance shall meet the requirements in Table 9 of GB/T 4797.6, enabling the product to operate normally in outdoor humid and salt spray environments.

6. Product Label

DC/DC ADAPTERMODEL: 8KW-DC-DCINPUT: DC800V-1000VOUTPUT: 60V-134AIP Rating: IP54Weight: 2.2Kg

7. Mechanical Dimensions and Connector Definition

7.1 Product Installation Dimension Diagram

Parameter	Index
Enclosure Dimension	187mm185mm70mm±1mm

7.2 Product Weight

Approx. 2.2KG

8. Packaging, Transportation, Storage

8.1 Packaging

The packing box shall be marked with product name, model, manufacturer's logo, inspection certificate from the manufacturer's quality department, manufacturing date, etc.; an accessory list shall be included in the packing box.

8.2 Transportation

The product shall be packed in a sturdy packing box during transportation.
The exterior of the box shall comply with the provisions of relevant national standards and be marked with signs such as "Handle with Care" and "Moisture-proof".
The packing boxes containing the products can be transported by any means of transportation.
Direct exposure to rain and snow and mechanical impact shall be avoided during transportation.

8.3 Storage

Unused products shall be stored in the packing boxes.
The warehouse environment shall have a temperature of -10℃~40℃ and a relative humidity not exceeding 80%.
The warehouse shall be free of harmful gases, flammable and explosive products, and corrosive chemicals, and shall be free from strong mechanical vibration, impact, and strong magnetic field.
The packing boxes shall be placed at least 20cm above the ground and at least 50cm away from walls, heat sources, windows, or air inlets.
The storage period under the specified conditions is generally 2 years. After 2 years, the product shall be re-inspected before use.

9. Safety Precautions

Once the safety protection of the equipment is damaged, the equipment must be stopped and handled in accordance with the relevant maintenance regulations.
When the power supply equipment is moved from a cold environment to a warm environment, condensation may cause electric leakage hazards. Therefore, the grounding requirement must be strictly implemented; only qualified personnel are allowed to connect the equipment to the power supply.
Before conducting maintenance on the power supply equipment, the power supply must be cut off and the equipment must be shut down for 5 minutes to allow sufficient time for the capacitors to discharge.
Pay attention to safety in use: Avoid touching parts marked with safety warning signs or high-voltage signs to prevent electric shock or burns.

10. Referenced Standards and Specifications

GB/T 2423.1-2001 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods - Test A: Low Temperature
GB/T 2423.2-2001 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods - Test B: High Temperature
GB/T 2423.3-1993 Basic Environmental Testing Procedures for Electrical and Electronic Products - Test Ca: Steady Damp Heat Test Method
GB/T 2423.4-1993 Basic Environmental Testing Procedures for Electrical and Electronic Products - Test Db: Alternating Damp Heat Test Method
GB/T 2423.5-1995 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods - Test Ea and Guidance: Shock
GB/T 2423.6-1995 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods - Test Ea and Guidance: Bump
GB/T 2423.8-1995 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods - Test Ed: Free Fall
GB/T 2423.10-1995 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods - Test Fc and Guidance: Vibration (Sinusoidal)
GB/T 2423.11-1997 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods - Test Fd: Broadband Random Vibration - General Requirements
GB/T 2423.22-2002 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods - Test N: Temperature Change
GB/T 14508-93 Mechanical Environmental Conditions for Grade Highway Freight Transportation
EN55022:1998 Information Technology Equipment - Radio Disturbance Characteristics - Limits and Measurement Methods
EN55024:1998 Information Technology Equipment - Immunity Characteristics - Limits and Measurement Methods
CEI IEC 61000-4-2 2001 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Electrostatic Discharge Immunity Test
CEI IEC 61000-4-3 2002 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Radiated, Radio-Frequency, Electromagnetic Field Immunity Test
CEI IEC 61000-4-4 1998 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Electrical Fast Transient/Burst Immunity Test
CEI IEC 61000-4-5 1999 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Surge (Impact) Immunity Test
CEI IEC 61000-4-6 2001 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Immunity to Conducted Disturbances, Induced by Radio-Frequency Fields
CEI IEC 61000-4-8 1993 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Power Frequency Magnetic Field Immunity Test
CEI IEC 61000-4-11 1994 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Voltage Dips, Short Interruptions and Voltage Variations Immunity Tests
CEI IEC 61000-4-29 2000 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Voltage Dips, Short Interruptions and Voltage Variations Immunity Tests for DC Input Ports
IEC 61000-3-2 2001 Electromagnetic Compatibility (EMC) - Limits - Limits for Harmonic Current Emissions (Equipment Input Current ≤16A per Phase)
IEC 61000-3-3 1994 Electromagnetic Compatibility (EMC) - Limits - Limitation of Voltage Fluctuations and Flicker in Low-Voltage Supply Systems (Equipment Rated Current ≤16A)
GB4943-2001 Safety of Information Technology Equipment
YD/T 282-2000 General Reliability Test Methods for Communication Equipment
GB/T 13722-92 Technical Requirements and Test Methods for Mobile Communication Power Supplies
YD/T 732-95 Inspection Methods for DC-DC Converters for Telecommunication
YD/T 731-2002 High-Frequency Switching Rectifiers for Telecommunication
GB14287.1-2005 Electrical Fire Monitoring Systems - Part 1: Electrical Fire Monitoring Devices

常见问题

1. 我如何下订单？

只需在产品页面选择您的款式，然后点击“加入购物车”按钮，按照简单的步骤完成您的订单。
我们会准备您的订单，并在发货时通知您！

2. 我的订单需要多长时间发货？

订单通常在5到10个工作日内发货。国际订单的运输时间将额外增加1到2周。

3. 我的追踪号码无法使用

追踪号码可能需要3-5天才能在运输承运商的系统中显示。偶尔，运输承运商可能会丢失订单。如果追踪号码在几天内仍然无法使用，请联系运输承运商。

4. 我需要帮助处理延迟订单

订单通常在5到8个工作日内发货。国际订单的运输时间将额外需要1到2周。
如果您的订单在10个工作日（国内）和20个工作日（国际）后仍未到达，请联系我们的团队，我们很乐意为您提供帮助。
需要定制的产品，生产时间为10-25天发货，产品详情将另行通知。

5. 我们接受以下安全支付方式：

信用卡（通过 Airwallex）：

Visa / 万事达卡 / 美国运通
由...保障Airwallex ，一个全球合规的支付平台

第三方支付：

PayPal（个人及商务账户）

银行转账：

企业账户转账（支持SWIFT/IBAN）

6. 我的卡什么时候会被扣款？

下单成功后立即。

7. 我的个人信息有多安全？

我们遵循最高行业标准，在您结账和购买时保护您的个人信息。
您的信用卡信息在传输过程中通过安全套接字层（SSL）技术加密，该技术在互联网上广泛用于处理支付。您的信用卡信息仅用于完成所请求的交易，之后不会被存储。

7.购物安全保障

我们使用PAYPAL收款。详情请查看PAYPAL官方网站，以保障您的购物资金安全。

https://www.paypal.com/webapps...

8. 什么配送？

我们与DHL、FedEx、EMS等快递公司合作，您可以在下单时自由选择；

DHL ： https://www.dhl.com/
FedEx ： https://www.fedex.com/
EMS： https://www.ems.com.cn/
物流追踪：https://www.uavmodel.com/apps/17TRACK

9.退款问题？

由于买方自身原因导致退款，本网站不承担包括退货运费在内的任何手续费。

定制产品：一旦客户提交订单，产品将立即进入生产阶段。鉴于其定制性质和生产的即时性，此类订单一经确认即具有约束力，恕不接受退款。

所有需要生产时间的产品均归类为定制产品。

查看详情

10、答案 : 清关责任取决于贸易条款（例如，EXW、FOB、DDP）。一般来说：

我们的默认条款客户（收货人）必须负责清关并支付所有关税/税费。
例外如果您的订单显示“DDP（完税后交货）”，我们将负责清关。

11、答案通常所需文件：

身份证（例如护照）或营业税号；
商业发票（购买后请联系我们）；
提示 : 请提前联系您当地的海关！

12、答案关税由您所在国家的海关根据产品类型、价值和法规确定。估算费用请参考：

请查看您当地的海关网站；
使用第三方工具（例如，Avalara，DutyCalculator）。

13、答案:

延迟: 直接联系海关提交文件/付款。我们可以提供追踪号码或发票。
破坏因未及时清关而产生的损失将由客户承担。
例外如果是由于我们的文档错误引起的，请联系我们寻求支持。

14、答案 您将通过电子邮件收到商业发票和装箱单。如需其他文件，请联系 sales@uavmodel.com （24小时内回复）。

15、答案以下产品可能会被扣押或拒收：

您所在国家禁止的物品（例如，含有禁用成分的化妆品）；
未获得必要认证的产品（例如，缺少CE标志的电子产品）；
申报价值过低（可能引发逃税嫌疑）。

如果您通过信用卡付款，您的付款可能会在结账时被我们的系统拒绝，以防止可能的信用卡欺诈。提前致电您的信用卡公司或银行，告知他们此次购买是个好主意，以免付款被拒绝。
在这种情况下，这里有三个解决方案供您选择：
1. 如果您有PayPal账户，请尝试通过PayPal付款。
2. 请切换到您的其他信用卡/借记卡。
3. 如果您没有PayPal账户，请在结账页面仍然选择PayPal并点击完成订单按钮。然后您将被引导到一个页面，可以访问PayPal和借记卡/信用卡支付（对于后者选项，您无需注册PayPal）。
按照以下步骤：

步骤 1. 选择 PayPal（即使您没有 PayPal 账户）

步骤 2. 点击“使用借记卡或信用卡支付”。

步骤 3. 填写您的信用卡信息并完成您的订单。

银行转账信息：

账户号码：63001185921
持有人名称：厦门高腾贸易有限公司
支持货币：AUD CAD CHF DKK EUR GBP HKD JPY NOK NZD SEK SGD USD ZAR
银行名称：摩根大通银行香港分行
银行位置国家：香港，中国
银行地址：香港中环干诺道8号，查特大厦
账户类型：活期
Swift/BIC: CHASHKHH (CHASHKHHXXX，如果需要11个字符)
路由号码：007863
银行代码：007
分行编号：863
请在付款时包含以下备忘录/信息给收款人：[买方姓名][发票/合同编号][产品]

所有权：无人机模型 CO., LIMITED；漳州亿诚科技有限公司；厦门高腾科技有限公司。

电子邮件：Sales@uavmodel.com

电话：+8613015671328

无人机模型

所有权：UAVMODEL CO., LIMITED; 漳州亿诚科技有限公司;厦门高腾科技有限公司

电子邮件：Sales@uavmodel.com

台湾投资区，交美镇，文埔工业园，景霞路25号313

厦门火炬高新区软件园集美北路1110号2502-3单元