UAVMODEL

WF-750S50-3K Power Module

Name: WF-750S50-3K Power Module
Brand: UAVMODEL
SKU: WF-750S50-3K
Price: 1470.00 USD
Availability: InStock

$1,470.00

WF-750S50-3K

产品型号

预计在付款后 30~40days 天内送达；

Checkout Securely with

无法下单的客户请联系我们；

Tag : battery power supply , drone power supply , Power Battery , Power Supply

1. Overview

1. Application

This high-voltage DC power supply is a custom-made special power supply, featuring small size, light weight, high efficiency, and built-in fan for heat dissipation. The maximum operating efficiency is ≥97%. The power module adopts an aluminum shell design, which is lightweight and aesthetic, with a waterproof design. It can be used as a substitute for imported high-voltage DC module power supplies.

2. Product Features

DC-DC Isolated Power Converter: Converts the input 750V DC power into 50V DC power in an isolated manner, with a total output power of 3000W.
High power density, small size, and light weight.
Design meets power supply reliability requirements: Input has over/undervoltage protection; output has overvoltage protection, current limiting, short-circuit, and overtemperature protection functions.

3. Product Photos

4. Main Product Specifications

Input Voltage Range	Rated Output Voltage	Rated Output Power	Efficiency	Voltage Regulation Accuracy	Output Ripple and Noise
700~750Vdc	50±0.5Vdc	3000W	≥96%	≤±1%	≤±2%Vo

2. Environmental Conditions

Serial Number	Item	Technical Index	Unit	Remarks
1	Operating Temperature	-40℃~+50℃	℃
2	Storage Temperature	-40℃~+80℃	℃	/
3	Relative Humidity	≤95	%	No Condensation (40℃±2℃)
4	Altitude	0-2000	m
5	Atmospheric Pressure	76~106	Kpa	/
6	Heat Dissipation Method	Built-in Air Cooling	/	/

3. Electrical Characteristics

Serial Number 1	Input Characteristics
Item	Technical Requirement	Unit	Remarks
1.1	Rated Input Voltage	725	Vdc
1.2	Input Voltage Range	700~750	Vdc
1.3	Maximum Input Current	5	A	In=700Vdc, Po=3000W
2	Output Characteristics
Serial Number	Item	Technical Requirement	Unit	Remarks
2.1	Rated Output Voltage	50	Vdc	/
2.2	Output Voltage Range	49.7~50.3	Vdc
2.3	Rated Output Current	60	A	/
2.4	Rated Output Power	3000	W	/
2.5	Output Efficiency	≥96	%	In=750Vdc, Full Load
2.6	Voltage Regulation Accuracy	±1	%	/
2.7	Source Regulation	±1	%	/
2.8	Load Regulation	±1	%	/
2.9	Output Ripple and Noise	±2	%/Vo	Bandwidth limited to 20MHz; 10uF electrolytic capacitor and 0.1uF film capacitor connected in parallel at the test terminal; Rated load
2.10	Temperature Coefficient	±0.02	%/℃	/
2.11	Output Rise Time	≤100	ms	/
2.12	Power-on Output Delay	≤5	S	Rated Input
2.13	Power-on/Power-off Overshoot Amplitude	△V: ≤±5	%	/
2.14	Transient Response Overshoot	△V: ≤±5	%	/

2.15	Transient Response Recovery Time	≤2	ms	75%~50% load change, 25℃; 25%~50%~25% or 50%~
3	Protection Characteristics
Serial Number	Item	Technical Requirement	Unit	Remarks
3.1	Input Undervoltage Protection	630~670	Vdc	Hysteresis greater than 10V
3.2	Input Undervoltage Recovery	≤700	Vdc
3.3	Input Overvoltage Protection	760~800	Vdc	Hysteresis greater than 10V
3.4	Input Overvoltage Recovery	≥750	Vdc
3.5	Input Reverse Connection Protection	No Damage Under Reverse Connection		Input 750Vdc reversed
3.6	Output Overvoltage Protection	54~59	Vdc	Self-recoverable
3.7	Output Overcurrent Protection	65~72	A	Self-recoverable
3.8	Output Short-Circuit Protection	Sustained Short-Circuit Tolerance		Self-recoverable
3.9	Overtemperature Protection	65	℃	Internal Thermistor Temperature
3.10	Overtemperature Recovery	60	℃
4	Parallel Current Sharing
Serial Number	Item	Technical Requirement	Unit	Remarks
4.1	Current Sharing Bus Voltage	Uniformly adjusted to 5Vdc±0.03Vdc at factory (At: 60A)
4.2	Current Sharing Imbalance	≤5	%	Output greater than 50% LOAD
4.3	Parallel Connection Method	Current sharing bus signals connected in parallel; load outputs connected in parallel
4.4	Number of Parallel Units	≤6	PCS

4. Safety Characteristics

Serial Number	Item		Test Condition	Remarks
1	Dielectric Strength	Input to Output	2500Vdc/2mA/1min	No Flashover, No Breakdown
		Input to Enclosure	2000Vdc/2mA/1min
		Output to Enclosure	500Vdc/2mA/1min
2	Insulation Resistance	Input to Output	≥10MΩ@500Vdc	Under normal atmospheric pressure, relative humidity 90%, test DC voltage 500V
		Input to Enclosure	≥10MΩ@500Vdc
		Output to Enclosure	≥10MΩ@500Vdc

5. Other Characteristics

1. Flame Retardant Requirements:

The flame retardant grade of the PCB used in the system shall meet the V-0 requirement specified in GB4943.1-2011. The flame retardant grade of insulated cables shall meet the requirements specified in GB/T 18380.12-2008. The flame retardant grade of other insulating materials shall meet the V1 requirement specified in GB4943.1-2011.

2. System Noise

The system noise shall not exceed 45dB(A).

3. System Reliability

MTBF ≥ 100Khour;Test Conditions: 25℃, rated input, full-load output; estimated by MIL-HDBK-217F Notice2 stress method;

4. Protection Level

The protection level shall meet the IP54 requirement. No water accumulation is allowed on the top of the power supply enclosure.

5. Three Protections (Moisture Proof, Mildew Proof, Salt Spray Proof)

Circuits such as printed circuit boards and connectors inside the product shall be treated with moisture proof, mildew proof, and salt spray proof. Among them, the salt spray resistance shall meet the requirements in Table 9 of GB/T 4797.6, enabling the product to operate normally in outdoor humid and sweat-salt spray environments.

6. Product Label

8. Packaging, Transportation, Storage

1. Packaging

The packing box shall be marked with product name, model, manufacturer's logo, inspection certificate from the manufacturer's quality department, manufacturing date, etc.; an accessory list shall be included in the packing box.

2. Transportation

The product shall be packed in a sturdy packing box during transportation. The exterior of the box shall comply with the provisions of relevant national standards and be marked with "Handle with Care", "Moisture Proof", etc. The packing boxes containing the products can be transported by any means of transportation. Direct exposure to rain and snow and mechanical impact shall be avoided during transportation.

3. Storage

Unused products shall be stored in packing boxes. The warehouse environment shall have a temperature of -10~40℃ and a relative humidity not exceeding 80%. No harmful gases, flammable and explosive products, or corrosive chemicals are allowed in the warehouse. There shall be no strong mechanical vibration, impact, or strong magnetic field. The packing boxes shall be padded to be at least 20cm above the ground and at least 50cm away from walls, heat sources, windows, or air inlets. The storage period under the specified conditions is generally 2 years. After 2 years, the product shall be re-inspected.

9. Safety Precautions

Once the safety protection of the equipment is damaged, the equipment must stop working and be handled in accordance with relevant maintenance regulations.
When the power supply equipment is moved from a cold environment to a warm environment, condensation may cause electric leakage hazards, so grounding requirements must be strictly implemented; only qualified personnel are allowed to connect the equipment to the power supply.
After cutting off the power supply, the equipment must be shut down for five minutes to allow sufficient time for the capacitors to discharge before maintenance work can be carried out on the power supply equipment.
Pay attention to safety during use: Avoid touching areas marked with safety warnings or high-voltage signs to prevent electric shock or scalding.

10. Referenced Standards and Specifications

GB/T 2423.1-2001 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods / Test A: Low TemperatureGB/T 2423.2-2001 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods / Test B: High TemperatureGB/T 2423.3-1993 Basic Environmental Testing Procedures for Electrical and Electronic Products - Test Ca: Steady Damp Heat Test MethodGB/T 2423.4-1993 Basic Environmental Testing Procedures for Electrical and Electronic Products - Test Db: Alternating Damp Heat Test MethodGB/T 2423.5-1995 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods / Test Ea and Guide: ImpactGB/T 2423.6-1995 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods / Test Ea and Guide: BumpGB/T 2423.8-1995 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods / Test Ed: Free FallGB/T 2423.10-1995 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods / Test Fc and Guide: Vibration (Sinusoidal)GB/T 2423.11-1997 Environmental Testing for Electrical and Electronic Products - Part 2: Test Methods / Test Fd: Broadband Random Vibration - General Requirements9GB/T 2423.22-2002 Environmental Testing for Electrical and Electronic Products - Part 2: Test N: Temperature ChangeGB/T 14508-93 Mechanical Environmental Conditions for Grade Highway Freight TransportationEN55022:1998 Information Technology Equipment - Radio Disturbance Characteristics - Limits and Measurement MethodsEN55024:1998 Information Technology Equipment - Immunity Characteristics - Limits and Measurement MethodsCEI IEC 61000-4-2 2001 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Electrostatic Discharge Immunity TestCEI IEC 61000-4-3 2002 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Radiated, Radio-Frequency, Electromagnetic Field Immunity TestCEI IEC 61000-4-4 1998 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Electrical Fast Transient/Burst Immunity TestCEI IEC 61000-4-5 1999 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Surge (Impact) Immunity TestCEI IEC 61000-4-6 2001 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Immunity to Conducted Disturbances, Induced by Radio-Frequency FieldsCEI IEC 61000-4-8 1993 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Power Frequency Magnetic Field Immunity TestCEI IEC 61000-4-11 1994 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Voltage Dips, Short Interruptions and Voltage Variations Immunity TestsCEI IEC 61000-4-29 2000 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Voltage Dips, Short Interruptions and Voltage Variations Immunity Tests for DC Input PortsIEC 61000-3-2 2001 Electromagnetic Compatibility (EMC) - Limits - Limits for Harmonic Current Emissions (Equipment Input Current ≤16A per Phase)IEC 61000-3-3 1994 Electromagnetic Compatibility (EMC) - Limits - Voltage Fluctuations and Flicker in Low-Voltage Supply Systems (Equipment Rated Current ≤16A)GB4943-2001 Safety of Information Technology EquipmentYD/T 282-2000 General Test Methods for Reliability of Telecommunication EquipmentGB/T 13722-92 Technical Requirements and Test Methods for Mobile Communication Power SuppliesYD/T 732-95 Test Methods for DC-DC Converters for TelecommunicationYD/T 731-2002 High-Frequency Switching Rectifiers for TelecommunicationGB14287.1-2005 Electrical Fire Monitoring Systems - Part 1: Electrical Fire Monitoring Devices

常见问题

1. 我如何下订单？

只需在产品页面选择您的款式，然后点击“加入购物车”按钮，按照简单的步骤完成您的订单。
我们会准备您的订单，并在发货时通知您！

2. 我的订单需要多长时间发货？

订单通常在5到10个工作日内发货。国际订单的运输时间将额外增加1到2周。

3. 我的追踪号码无法使用

追踪号码可能需要3-5天才能在运输承运商的系统中显示。偶尔，运输承运商可能会丢失订单。如果追踪号码在几天内仍然无法使用，请联系运输承运商。

4. 我需要帮助处理延迟订单

订单通常在5到8个工作日内发货。国际订单的运输时间将额外需要1到2周。
如果您的订单在10个工作日（国内）和20个工作日（国际）后仍未到达，请联系我们的团队，我们很乐意为您提供帮助。
需要定制的产品，生产时间为10-25天发货，产品详情将另行通知。

5. 我们接受以下安全支付方式：

信用卡（通过 Airwallex）：

Visa / 万事达卡 / 美国运通
由...保障Airwallex ，一个全球合规的支付平台

第三方支付：

PayPal（个人及商务账户）

银行转账：

企业账户转账（支持SWIFT/IBAN）

6. 我的卡什么时候会被扣款？

下单成功后立即。

7. 我的个人信息有多安全？

我们遵循最高行业标准，在您结账和购买时保护您的个人信息。
您的信用卡信息在传输过程中通过安全套接字层（SSL）技术加密，该技术在互联网上广泛用于处理支付。您的信用卡信息仅用于完成所请求的交易，之后不会被存储。

7.购物安全保障

我们使用PAYPAL收款。详情请查看PAYPAL官方网站，以保障您的购物资金安全。

https://www.paypal.com/webapps...

8. 什么配送？

我们与DHL、FedEx、EMS等快递公司合作，您可以在下单时自由选择；

DHL ： https://www.dhl.com/
FedEx ： https://www.fedex.com/
EMS： https://www.ems.com.cn/
物流追踪：https://www.uavmodel.com/apps/17TRACK

9.退款问题？

由于买方自身原因导致退款，本网站不承担包括退货运费在内的任何手续费。

定制产品：一旦客户提交订单，产品将立即进入生产阶段。鉴于其定制性质和生产的即时性，此类订单一经确认即具有约束力，恕不接受退款。

所有需要生产时间的产品均归类为定制产品。

查看详情

10、答案 : 清关责任取决于贸易条款（例如，EXW、FOB、DDP）。一般来说：

我们的默认条款客户（收货人）必须负责清关并支付所有关税/税费。
例外如果您的订单显示“DDP（完税后交货）”，我们将负责清关。

11、答案通常所需文件：

身份证（例如护照）或营业税号；
商业发票（购买后请联系我们）；
提示 : 请提前联系您当地的海关！

12、答案关税由您所在国家的海关根据产品类型、价值和法规确定。估算费用请参考：

请查看您当地的海关网站；
使用第三方工具（例如，Avalara，DutyCalculator）。

13、答案:

延迟: 直接联系海关提交文件/付款。我们可以提供追踪号码或发票。
破坏因未及时清关而产生的损失将由客户承担。
例外如果是由于我们的文档错误引起的，请联系我们寻求支持。

14、答案 您将通过电子邮件收到商业发票和装箱单。如需其他文件，请联系 sales@uavmodel.com （24小时内回复）。

15、答案以下产品可能会被扣押或拒收：

您所在国家禁止的物品（例如，含有禁用成分的化妆品）；
未获得必要认证的产品（例如，缺少CE标志的电子产品）；
申报价值过低（可能引发逃税嫌疑）。

如果您通过信用卡付款，您的付款可能会在结账时被我们的系统拒绝，以防止可能的信用卡欺诈。提前致电您的信用卡公司或银行，告知他们此次购买是个好主意，以免付款被拒绝。
在这种情况下，这里有三个解决方案供您选择：
1. 如果您有PayPal账户，请尝试通过PayPal付款。
2. 请切换到您的其他信用卡/借记卡。
3. 如果您没有PayPal账户，请在结账页面仍然选择PayPal并点击完成订单按钮。然后您将被引导到一个页面，可以访问PayPal和借记卡/信用卡支付（对于后者选项，您无需注册PayPal）。
按照以下步骤：

步骤 1. 选择 PayPal（即使您没有 PayPal 账户）

步骤 2. 点击“使用借记卡或信用卡支付”。

步骤 3. 填写您的信用卡信息并完成您的订单。

银行转账信息：

账户号码：63001185921
持有人名称：厦门高腾贸易有限公司
支持货币：AUD CAD CHF DKK EUR GBP HKD JPY NOK NZD SEK SGD USD ZAR
银行名称：摩根大通银行香港分行
银行位置国家：香港，中国
银行地址：香港中环干诺道8号，查特大厦
账户类型：活期
Swift/BIC: CHASHKHH (CHASHKHHXXX，如果需要11个字符)
路由号码：007863
银行代码：007
分行编号：863
请在付款时包含以下备忘录/信息给收款人：[买方姓名][发票/合同编号][产品]

所有权：无人机模型 CO., LIMITED；漳州亿诚科技有限公司；厦门高腾科技有限公司。

电子邮件：Sales@uavmodel.com

电话：+8613015671328

无人机模型

所有权：UAVMODEL CO., LIMITED; 漳州亿诚科技有限公司;厦门高腾科技有限公司

电子邮件：Sales@uavmodel.com

台湾投资区，交美镇，文埔工业园，景霞路25号313

厦门火炬高新区软件园集美北路1110号2502-3单元