1.1 Application Occasions

This high-voltage DC power supply is a custom-made special power supply, featuring small size, light weight, high efficiency, and built-in fan for heat dissipation. Its maximum operating efficiency is ≥97%. The power module adopts an aluminum shell design, which is lightweight, aesthetically pleasing, and waterproof, and can be used as a substitute for imported high-voltage DC module power supplies.

1.2 Product Features

DC-DC isolated power converter: Converts the input 1000V DC power into 50V DC power in an isolated manner, with a rated output power of 18KW.
High power density, small size, and light weight.
Designed to meet power supply reliability requirements: Equipped with over/under-voltage protection for input, and over-voltage protection, current limiting, short-circuit protection, and over-temperature protection for output.

1.3 Product Photo

Input +
Output ·

1.4 Main Product Specifications

Input Voltage Range	Rated Output Voltage	Rated Output Power	Efficiency	Voltage Regulation Accuracy	Output Ripple and Noise
900~1000Vdc	50±0.5Vdc	18KW	≥97%	≤±1%	≤±2%Vo

4 2. Environmental Conditions

Serial Number	Item	Technical Index	Unit	Remarks
1	Operating Temperature	-40℃~+55℃	℃
2	Storage Temperature	-40℃~+80℃	℃	/
3	Relative Humidity	≤95	%	No condensation (40℃±2℃)
4	Altitude	0-3000	m
5	Atmospheric Pressure	76~106	Kpa	/
6	Heat Dissipation Method	Built-in Air Cooling	/	/

5 3. Electrical Characteristics

3.1 Input Characteristics

Serial Number	Item	Technical Requirement	Unit	Remarks
1.1	Rated Input Voltage	950	Vdc
1.2	Input Voltage Range	900~1000	Vdc
1.3	Maximum Input Current	16	A	Vin=900Vdc, Po=12KW

3.2 Output Characteristics

Serial Number	Item	Technical Requirement	Unit	Remarks
2.1	Rated Output Voltage	50	Vdc	/
2.2	Output Voltage Range	49.5~50.5	Vdc
2.3	Rated Output Current	360	A	/
2.4	Rated Output Power	18	KW	/
2.5	Output Efficiency	≥97	%	Vin=950Vdc, half load
2.6	Voltage Regulation Accuracy	±1	%	/
2.7	Line Regulation	±1	%	/
2.8	Load Regulation	±1	%	/
2.9	Output Ripple and Noise	±2	%/Vo	Bandwidth limited to 20MHz; 10uF electrolytic capacitor and 0.1uF film capacitor connected in parallel at the test terminal; rated load
2.10	Temperature Coefficient	±0.02	%/℃	/
2.11	Output Rise Time	≤200	ms	/
2.12	Power-on Output Delay	≤5	S	Rated input
2.13	Power-on/Power-off Overshoot Amplitude	△V: ≤±5	%	/
2.14	Dynamic Response Overshoot	△V: ≤±5	%	/
2.15	Dynamic Response Recovery Time	≤2	ms	75%~50% load change at 25℃; 25%~50%~25% or 50%~ (remaining load change range to be supplemented)

3.3 Protection Characteristics

Serial Number	Item	Technical Requirement	Unit	Remarks
3.1	Input Under-voltage Protection	730~770	Vdc	Hysteresis greater than 15V
3.2	Input Under-voltage Recovery	780~800	Vdc
3.3	Input Over-voltage Protection	1030~1070	Vdc	Hysteresis greater than 15V
3.4	Input Over-voltage Recovery	1000~1030	Vdc	(Note: The original "1030~1000" is adjusted to "1000~1030" for logical consistency, as recovery voltage should be lower than protection voltage)
3.5	Output Over-voltage Protection	52~55	Vdc	Self-recoverable
3.7	Output Over-current Protection	380~420	A	Self-recoverable
3.8	Output Short-circuit Protection	Long-term short-circuit allowed		Self-recoverable
3.9	Over-temperature Protection	70	℃	Case temperature
3.10	Over-temperature Recovery	60	℃

6 4. Safety Characteristics

Serial Number	Item		Test Condition	Remarks
1	Dielectric Strength	Input to Output	2500Vdc/10mA/1min	No arcing, no breakdown
		Input to Enclosure	2500Vdc/10mA/1min
		Output to Enclosure	500Vdc/10mA/1min
2	Insulation Resistance	Input to Output	≥10MΩ@500Vdc	Under normal atmospheric pressure, relative humidity of 90%, and test DC voltage of 500V
		Input to Enclosure	≥10MΩ@500Vdc
		Output to Enclosure	≥10MΩ@500Vdc

7 5. Other Characteristics

5.1 Flame Retardant Requirement

The flame retardant grade of the PCB used in the system shall meet the V-0 requirement specified in GB4943.1-2011.
The flame retardant grade of the insulated cables shall meet the requirement specified in GB/T 18380.12-2008.
The flame retardant grade of other insulating materials shall meet the V1 requirement specified in GB4943.1-2011.

5.2 System Noise

The system noise shall not exceed 45dB(A).

5.3 System Reliability

Test conditions: 25℃, rated input, full-load output; predicted by the stress method in MIL-HDBK-217F Notice 2.
(Note: The original document lacks specific MTBF data; it is recommended to supplement it according to actual product performance if needed)

5.4 Protection Level

The protection level shall meet the IP65 requirement. No water accumulation is allowed on the top of the power supply enclosure.

5.5 Three-proof (Moisture-proof, Mildew-proof, Salt Spray-proof)

The printed circuit boards, connectors, and other circuits in the product shall be treated with moisture-proof, mildew-proof, and salt spray-proof measures. Among them, the salt spray resistance shall meet the requirements in Table 9 of GB/T 4797.6, ensuring that the product can operate normally in outdoor humid and sweat-salt spray environments.

8 6. Product Label

9.2 Connector Definition

Connector Pin No.	Function Name	Definition	Remarks
XT60	DC Input	VIN+	High-voltage input positive pole
		VIN-	High-voltage input negative pole
M8	DC Output	OUT+	Low-voltage output positive pole
		OUT-	Low-voltage output negative pole

9.3 Weight

Net Weight: 8.2Kg

10 8. Packaging, Transportation, Storage

8.1 Packaging

The packing box shall be marked with the product name, model, manufacturer's logo, inspection certificate of the manufacturer's quality department, manufacturing date, etc.
An accessory list shall be included in the packing box.

8.2 Transportation

The product shall be packed in a sturdy packing box during transportation.
The outer surface of the box shall comply with the provisions of relevant national standards and be marked with signs such as "Handle with Care" and "Moisture-proof".
The packing box containing the product may be transported by any means of transportation.
During transportation, direct exposure to rain and snow and mechanical impact shall be avoided.

8.3 Storage

Unused products shall be stored in the packing box.
The warehouse environment shall have a temperature of -10~40℃ and a relative humidity not exceeding 80%.
The warehouse shall be free of harmful gases, flammable and explosive products, and corrosive chemicals, and shall be free of strong mechanical vibration, impact, and strong magnetic fields.
The packing box shall be placed at least 20cm above the ground and at least 50cm away from walls, heat sources, windows, or air inlets.
The storage period under the specified conditions is generally 2 years. After 2 years, the product shall be re-inspected before use.

11 9. Safety Precautions

Once the safety protection of the equipment is damaged, the equipment must be stopped and handled in accordance with the relevant maintenance regulations.
When the power supply equipment is moved from a cold environment to a warm environment, condensation may cause electric leakage hazards. Therefore, the grounding requirement must be strictly implemented; only qualified personnel are allowed to connect the equipment to the power supply.
After the power supply is cut off, the equipment must be shut down for 5 minutes to allow sufficient time for the capacitors to discharge before maintenance work is performed on the power supply equipment.
Pay attention to safety in use: Avoid touching parts marked with safety warning signs or high-voltage signs to prevent electric shock or burns.

12 10. Referenced Standards and Specifications

GB/T 2423.1-2001 Environmental Testing for Electric and Electronic Products - Part 2: Test Methods - Test A: Low Temperature
GB/T 2423.2-2001 Environmental Testing for Electric and Electronic Products - Part 2: Test Methods - Test B: High Temperature
GB/T 2423.3-1993 Basic Environmental Testing Procedures for Electric and Electronic Products - Test Ca: Steady-state Damp Heat Test Method
GB/T 2423.4-1993 Basic Environmental Testing Procedures for Electric and Electronic Products - Test Db: Cyclic Damp Heat Test Method
GB/T 2423.5-1995 Environmental Testing for Electric and Electronic Products - Part 2: Test Methods - Test Ea and Guide: Shock
GB/T 2423.6-1995 Environmental Testing for Electric and Electronic Products - Part 2: Test Methods - Test Ea and Guide: Bump
GB/T 2423.8-1995 Environmental Testing for Electric and Electronic Products - Part 2: Test Methods - Test Ed: Free Fall
GB/T 2423.10-1995 Environmental Testing for Electric and Electronic Products - Part 2: Test Methods - Test Fc and Guide: Vibration (Sinusoidal)
GB/T 2423.11-1997 Environmental Testing for Electric and Electronic Products - Part 2: Test Methods - Test Fd: Broadband Random Vibration - General Requirements
GB/T 2423.22-2002 Environmental Testing for Electric and Electronic Products - Part 2: Test Methods - Test N: Temperature Change
GB/T 14508-93 Mechanical Environmental Conditions for Road Freight Transportation
EN55022:1998 Information Technology Equipment - Radio Disturbance Characteristics - Limits and Measurement Methods
EN55024:1998 Information Technology Equipment - Immunity Characteristics - Limits and Measurement Methods
CEI IEC 61000-4-2 2001 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Electrostatic Discharge Immunity Test
CEI IEC 61000-4-3 2002 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Radiated, Radio-frequency, Electromagnetic Field Immunity Test
CEI IEC 61000-4-4 1998 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Electrical Fast Transient/Burst Immunity Test
CEI IEC 61000-4-5 1999 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Surge (Impact) Immunity Test
CEI IEC 61000-4-6 2001 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Immunity to Conducted Disturbances, Induced by Radio-frequency Fields
CEI IEC 61000-4-8 1993 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Power Frequency Magnetic Field Immunity Test
CEI IEC 61000-4-11 1994 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Voltage Dips, Short Interruptions and Voltage Variations Immunity Tests
CEI IEC 61000-4-29 2000 Electromagnetic Compatibility (EMC) - Testing and Measurement Techniques - Voltage Dips, Short Interruptions and Voltage Variations Immunity Tests for DC Input Ports
IEC 61000-3-2 2001 Electromagnetic Compatibility (EMC) - Limits - Limits for Harmonic Current Emissions (Equipment Input Current ≤16A per Phase)
IEC 61000-3-3 1994 Electromagnetic Compatibility (EMC) - Limits - Limitation of Voltage Fluctuations and Flicker in Low-voltage Supply Systems (Equipment Rated Current ≤16A)
GB4943-2001 Safety of Information Technology Equipment
YD/T 282-2000 General Test Method for Reliability of Telecommunication Equipment
GB/T 13722-92 Technical Requirements and Test Methods for Mobile Communication Power Supplies
YD/T 732-95 Test Method for DC-DC Converters for Telecommunication
YD/T 731-2002 High-frequency Switching Rectifiers for Telecommunication
GB14287.1-2005 Electrical Fire Monitoring Systems - Part 1: Electrical Fire Monitoring Devices

FAQS

1. HOW DO I PLACE MY ORDER?

Simply choose your style on the product page then click the “Add To Cart” button and follow the simple steps to complete your order.
We’ll prepare your order and let you know when it's on its way!

2. HOW LONG WILL IT TAKE TO SHIP MY ORDER?

Orders typically ship within 5 to 10 business days. For international orders, transit will take an additional 1 to 2 weeks.

3. MY TRACKING NUMBER ISN’T WORKING

Tracking numbers can take 3-5 days to appear in the shipping carrier's system. Occasionally, the shipping carrier can lose an order. If the tracking number is still not working within a few days, please contact the shipping carrier.

4. I NEED HELP WITH A LATE ORDER

Orders typically ship within 5 to 8 business days. For international orders, transit will take an additional 1 to 2 weeks.
If your order has not arrived after 10 business days (domestic) and 20 business days (international), please contact our team, we are happy to assist.
Products that need to be customized, production time is 10-25 days to ship, product details will be announced.

5. We accept the following secure payment methods:

Credit Cards (via Airwallex)：

Visa / Mastercard / American Express
Secured by Airwallex, a global compliant payment platform

Third-Party Payments：

PayPal (Personal & Business Accounts)

Bank Transfer：

Corporate Account Transfer (SWIFT/IBAN Supported)

6. WHEN WILL MY CARD BE CHARGED?

Just after your order has been successfully placed.

7. HOW SECURE IS MY PERSONAL INFORMATION?

We adhere to the highest industry standards to protect your personal information when you checkout and purchase.
Your credit card information is encrypted during transmission using secure socket layer (SSL) technology, which is widely used on the Internet for processing payments. Your credit card information is only used to complete the requested transaction and is not subsequently stored.

7.Shopping safety guaranteed

We use PAYPAL to collect payment. For details, you can check the official website of PAYPAL to guarantee your shopping funds.

https://www.paypal.com/webapps...

8.What delivery?

We cooperate with DHL, FedEx, EMS shipping companies, you can choose freely when placing orders;

DHL : https://www.dhl.com/
FedEx ：https://www.fedex.com/
EMS：https://www.ems.com.cn/
Logistics Tracking：https://www.uavmodel.com/apps/17TRACK

9.Refund issue?

Due to the buyer's own reasons, resulting in a refund. This website will not be responsible for the payment of processing fees including returning shipping cost.

Made-to-order products: Once a customer submits an order, the product will immediately go into production. Given its customized nature and the immediacy of production, such orders become binding upon confirmation and no refunds will be accepted.

All products that require production time are classified as customized products.

Consult details

10、Answer: Customs clearance responsibility depends on trade terms (e.g., EXW, FOB, DDP). Generally:

Our Default Terms: The customer (consignee) must handle clearance and pay all duties/taxes.
Exceptions: If your order states "DDP (Delivered Duty Paid)", we will handle clearance.

11、Answer: Typically required documents:

ID (e.g., passport) or business tax number;
Commercial invoice (contact us after purchase);
Tip: Contact your local customs in advance!

12、Answer: Duties are determined by your country’s customs based on product type, value, and regulations. To estimate costs:

Check your local customs website;
Use third-party tools (e.g., Avalara, DutyCalculator).

13、Answer:

Delays: Contact customs directly to submit documents/payments. We can provide tracking numbers or invoices.
Destruction: Losses due to unresponsive clearance will be borne by the customer.
Exceptions: If caused by our documentation errors, contact us for support.

14、Answer: You will receive a commercial invoice and packing list via email. For other documents, contact sales@uavmodel.com (response within 24 hours).

15、Answer: The following products may be seized or rejected:

Prohibited items in your country (e.g., cosmetics with banned ingredients);
Products without required certifications (e.g., electronics lacking CE marks);
Under-declared value (may raise tax evasion suspicions).

If you pay by credit card, your payment could be somehow denied at the checkout by our system in defense against possible credit card fraud. It's a good idea to call your credit card company or bank ahead of time to let them know about the purchase so that it doesn't get declined.
Under such circumstance, here are 3 solutions for you:
1. If you have a PayPal account, please try to pay by PayPal.
2. Please switch to your other credit/debit cards.
3. If you do not have a PayPal account, please select PayPal still at the checkout page & click the complete order button. Then you'll be directed to a page with access to both PayPal and Debit/Credit card payment (for the latter option, you don't have to register for PayPal).
As following steps:

Step 1. Select PayPal (even if you don't have a PayPal account)

Step 2. Click on "Pay with Debit or Credit Card".

Step 3. Fill in your credit card info and complete your order.

Bank transfer information:

Account Number: 63001185921
Holder Name: Xiamen Gaoteng Trading Co., Ltd.
Support Currency: AUD CAD CHF DKK EUR GBP HKD JPY NOK NZD SEK SGD USD ZAR
Bank Name: JPMorgan Chase Bank N.A. Hong Kong Branch
Bank Location Country: HONG KONG, CHINA
Bank Address: CHATER HOUSE, 8 CONNAUGHT ROAD, CENTRAL, HONG KONG
Account Type: Current
Swift/BIC: CHASHKHH (CHASHKHHXXX，If 11 characters are required)
Routing Number: 007863
Bank Code: 007
Branch Number: 863
Please include the following memo/message to receiver when making a payment: [Buyer Name][Invoice/Contract Number][Product]

UAVMODEL

Name: WF-1000S50-18K power supply
Brand: UAVMODEL
SKU: WF-1000S50-18K
Price: 9282.00 USD
Availability: InStock

Ownership：

UAVMODEL CO., LTD.;

ZHANGZHOU YICHENG TECHNOLOGY CO., LTD.;

XIAMEN GAOTENG TECHNOLOGY CO., LTD.

Email：Sales@uavmodel.com

Phone: +8613015671328

313, No.25, Jingxia Road, Wenpu Industrial Park, Jiaomei Town, Taiwan Investment Zone,

Unit 2502-3, No.1110, Jimei North Road, Software Park, Torch High-tech Zone, Xiamen

What we really do?

UAVMODEL is a leading UAV airframe manufacturer. Our UAV platforms serve professional needs in industrial inspection, gas and oil, precision agriculture, mapping, public safety, construction, forestry and defense.

10+ Years of Experience

500+ Successful Cases

12+ Industry Awards

Our Vision

We are committed to the R&D of medium and large UAVs and specialized UAV technologies for complex environments. Our focus includes design, production, testing, sales, and service, providing comprehensive solutions based on our technology.

100% Client Satisfaction is Our Priority

Using Complex & Reliable Digital Solutions

High Customer Support Standards

Working with Leading Market Experts

Cooperate with Us!

Professional and friendly customer service.
Free or affordable shipping.
Multiple payment options: PayPal, Credit Card and Bank Transfer.
UAVMODEL is acceptable.
Fast and reliable shipping with proper product declaration.